Diagnostic Tool Lexia-3 For Citroen/Peugeot
Diagnostic Tool Lexia-3 for Citroen/Peugeot
Reviews / Howto / FAQ / Specifications of Diagnostic Tool Lexia-3 for Citroen/Peugeot
This is the latest version PP2000/LEXIA-3 Interface, which can work for both Citroen and Peugeot! This diagnostics software allows you to perform complete diagnostics of all from 1995 until present models.
Specifications:
This is the latest version PP2000/LEXIA-3 Interface, which can work for both Citroen and Peugeot! This diagnostics software allows you to perform complete diagnostics of all from 1995 until present models. Diagnostics is performed via OBD2 connector (which is located near steering wheel) or via manufacturer-specific connector (only older cars, pre-2001).
Functions:
Unlike other universal car scanner tools which only read fault codes, this software performs nearly all the functions like the original dealer diagnostic tool. Our diagnostic interface contains K-Line multiplexor, CAN-BUS interfaces and SAE J1850 bus (both PWM and VPW).
1. Read identification
Show complete identification of control unit, for example, part number, software/hardware version, manufacturer, etc…
2. Read fault codes
Show all stored and pending fault codes with complete description (for example. “Rail pressure – too low pressure”).
Program supports report printing or copy to clipboard.
3. Clear fault codes
It can clears all stored fault codes and other diagnostic information.
4. Auto-scan (complete car scan/test)
Detects all ECUs (electronic control units) installed in car and reads all diagnostic fault codes.
5. Measured Values
Program displays live Data like Engine Speed, Battery voltage, Oxygen Sensor, Coolant Temperature, etc. Values can be displayed in graph, 9 values at once, or full listing (all measured values). Logging to file is also supported, which allows offline analysis.
6. Actuator test
Actuator test activates particular actuator (e.g. turn on fuel pump, lock/unlock wheel, lock/unlock doors, cut off fuel, etc…)
7. Programming functions/Adaptation
This feature is of great importance in all vehicles because systems like Engine control units, Immobilizers, Airbags, Alarms, Body Control Units, and some others, require you to perform reset or programming procedures after car repair is done or even configuration after replacing broken Control Unit.
Hardware and software requirements
Software requires at least Intel Celeron/Pentium III 400 MHz, 128 MB RAM, 50MB free HDD space and USB 1.1 port (USB 2.0 recommended) and Microsoft Windows 98 SR2/2000/XP with the latest service pack installed.
If customer requires, we can prepare ready to work PC.
Instruction:
Go to your computer’s control panel
]]>
Set the area/language to USA/English
Start the installation
Make sure set the customer code as GB 0001
Follow the screen tips to install the software
When you get the register screen, please copy the screen and send it to us. We will send the activation code in several minutes.
Accessories:
Main unit with extension OBD2 cable
USB cable
Software CD for LEXIA-3 Version 45
Software CD for PP2000 Version 21
Instruction for PP2000
Images from BuyOnMe
MB STAR C4 Compatible with All Computers
Reviews / Howto / FAQ / Specifications of MB STAR C4 Compatible with All Computers
MB Star Compact-4 is the lately updated professional diagnostic equipment for Benz cars manufactured after year 2000. It is a little different from Compact3 in shape, which is smaller and lighter than Compact3. C4 2008 can do all what Compact3 can do and it is the replacement of Compact3-Star. It can not only work on IBM T30, now it can work on all types of computer, great convenient for you!
Specifications
MB STAR C4 Version: March 2009
C4 operating based on the Windows XP system, it includes workshops information system (WIS system), the movement management system and the automatically diagnose system (the DAS system). C4 2008 STAR works with original computer (COMPACT3) via both of RS232 and 485 protocols. Power can be supplied to original computer (COMPACT3) through the cables.Compact3 star can diagnose varied cars, trucks, buses of Mercedes Benz making.
Features:
1. This product has two version of hard disk. One version of hard disk is required to use on IBM T30. Another version of hard disk can fits all type of computer.
2. MB Star C4 has rs232/485 interface, which can connect with touch screen and also common screen.
3. MB Star C4 can work in the voltage of 12V/24V.
4. MB Star C4 can supply power to the computer by Power Cable.
Accessories:
1.1pc x C4 Multiplexer
2.1pc x 14 pin Connector
3.1pc x 16 Pin Connector
4.1pc x OBD2 Cable
5.1pc x 4 Pin Cable
6.1pc x 14 Pin Cable
7.1pc x Communication Cable
8.1pc x 38 Pin Cable
9.1pc x HDD
Images from BuyOnMe
GT1 Pro Fit all computer for BMW
Reviews / Howto / FAQ / Specifications of GT1 Pro Fit all computer for BMW
On vehicle models from the E65 on, BMW is for the first time using fiber-optic cables as standard to communicate between control units. The optical buses are notable for their high data transmission rate and they are not susceptible to electromagnetic interference. The optical buses in question are the MOST bus, primarily used for in-car entertainment electronics, and the byte flight bus, which serves predominantly safety-critical functions.
Specifications
DIS V57 SSS V32
On vehicle models from the E65 on, BMW is for the first time using fiber-optic cables as standard to communicate between control units.
The optical buses are notable for their high data transmission rate and they are not susceptible to electromagnetic interference. The optical buses in question are the MOST bus, primarily used for in-car entertainment electronics, and the byte flight bus, which serves predominantly safety-critical functions.
OPPS has been designed for encoding, individualizing and programming (CIP) via the Software Service Station (SSS) and envisaged for use as part of the BMW diagnostic system (DIS) from DISPlus and Group Tester One (GT1). It is intended for testing and programming tasks from the E65 series, taking the place of the diagnostic head.
OPS are intended for rapid programming of control units.
When operated at the SSS, no diagnostic or technical measuring procedures are possible, as no measuring technology is incorporated; in this instance, OPPS / OPS are used predominantly for programming control units (flashing). Communication with the vehicle can be performed both via the MOST and via the OBD interface. The OBD interface is required for the power supply to the OPPS / OPS and has communication properties via which the vehicle can be identified and the data to be programmed can be determined. From CIP version 7.0, it is possible to delete fault code memories via OPPS / OPS.
D-CAN included for diagnose on the following models:
- E60, E61 as of model year 03/2007
- E83 as of model year 09/2006
- E81, E87 as of model year 03/2007
- E90, E91, E92, E93 as of model year 03/2007
- E70 (new X5)
- R56 (new MINI)
OPS with DIS for diagnosis Supported Models:
Vehicle interface via OBD-II socket:
E87, E90, E91, E92, E60, E61, E63, E64, E65, E66, E70, E83, E85, E86, E38 (OBD-II), E39 (OBD-II), E46 (OBD-II), E52, E53, R56, R50, R52, R53
OPS with SSS for programming Supported Models:
(1) Vehicle interface via OBD-II socket:
E87, E90, E91, E92, E60, E61, E63, E64, E65, E66, E70, E83, R56, R50, R52, R53
(2) MOST compatibility (multichannel programming):
E87, E90, E91, E92, E60, E61, E63, E64, E65, E66, E70, R56, R50, R52, R53
Standard Configuration:
1. OPS multiplexer
2. OBD-II diagnostic cable
3. LAN cable
4. OPS MOST cable
5. 120G HDD with preinstalled SSS V32 for IBM T30
6. 120G HDD with preinstalled DIS V57 for IBM T30
Images from BuyOnMe
Couldn?t be written any better. Reading this post reminds me of my old room mate! He always kept talking about this. I will forward this article to him. Pretty sure he will have a good read. Thanks for sharing!